Cup Holder for Cans and Bottles
With Pre-Drilled Mounting Holes
Fit Details
Fits to Dashmounts or your own solution.
$24.90
This angled dash mount is custom designed for the Toyota Corolla (2002 to 2007). It fits into the shape of your dashboard, so your phone or device sits in clear view and within easy reach, and it stays put on rough roads. There are no holes to drill and no glue.
It is the mount on its own. You choose the holder to go with it, and it screws straight onto the mount with the screws provided. We make holders for phones, tablets, UHF radios and navigation units, so you can set the car up for whatever you carry and swap the holder later if your device changes.
| This Mount Fits | Toyota Corolla Year(s):02-07 |
| SKU | 653020 |
| Barcode # | 7320286530200 |
| Brand | ClicOn |
| Shipping Weight | 0.1000kg |
Below you will find the installation instructions for the Angled Mount (SKU:653020), you can click on the images to open a larger version in a new tab
1. The attaching part (the smallest part) The ClicOn face plate 1. Press the thin end of the enclosed gap openers into the gap between the control panel and the dashboard to widen the gap. 2. Peel off the cover of the adhesive tape on Part 1. Press Part 1 into the gap between the gap openers. Press to the left on Part 1, away from the steering wheel, so the angled edge hooks under/behind the control panel and the adhesive attaches to the dashboard. Pull out the gap openers. 3. Open up the predrilled holes in with a screwdriver (Philips). Peel off the cover of the adhesive tape on Place onto Part 1 so the holes match. Screw onto Part 1 with the enclosed screws. NOTE! Screw the screws straight into Part 1, in the same angle as Part 1. The ClicOn is in place.
1. The attaching part (the smallest part) The ClicOn face plate 1. Press the thin end of the enclosed gap openers into the gap between the control panel and the dashboard to widen the gap. 2. Peel off the cover of the adhesive tape on Part 1. Press Part 1 into the gap between the gap openers. Press to the left on Part 1, away from the steering wheel, so the angled edge hooks under/behind the control panel and the adhesive attaches to the dashboard. Pull out the gap openers. 3. Open up the predrilled holes in with a screwdriver (Philips). Peel off the cover of the adhesive tape on Place onto Part 1 so the holes match. Screw onto Part 1 with the enclosed screws. NOTE! Screw the screws straight into Part 1, in the same angle as Part 1. The ClicOn is in place.
1. The attaching part (the smallest part) The ClicOn face plate 1. Press the thin end of the enclosed gap openers into the gap between the control panel and the dashboard to widen the gap. 2. Peel off the cover of the adhesive tape on Part 1. Press Part 1 into the gap between the gap openers. Press to the left on Part 1, away from the steering wheel, so the angled edge hooks under/behind the control panel and the adhesive attaches to the dashboard. Pull out the gap openers. 3. Open up the predrilled holes in with a screwdriver (Philips). Peel off the cover of the adhesive tape on Place onto Part 1 so the holes match. Screw onto Part 1 with the enclosed screws. NOTE! Screw the screws straight into Part 1, in the same angle as Part 1. The ClicOn is in place.
1. The attaching part (the smallest part) The ClicOn face plate 1. Press the thin end of the enclosed gap openers into the gap between the control panel and the dashboard to widen the gap. 2. Peel off the cover of the adhesive tape on Part 1. Press Part 1 into the gap between the gap openers. Press to the left on Part 1, away from the steering wheel, so the angled edge hooks under/behind the control panel and the adhesive attaches to the dashboard. Pull out the gap openers. 3. Open up the predrilled holes in with a screwdriver (Philips). Peel off the cover of the adhesive tape on Place onto Part 1 so the holes match. Screw onto Part 1 with the enclosed screws. NOTE! Screw the screws straight into Part 1, in the same angle as Part 1. The ClicOn is in place.
Custom-designed Toyota Corolla (02-07) angled dash mount, CNC-machined in Sweden for a solid, secure fit. No holes, no drilling, no glue. Ready for you to add the holder made for your phone or other device (screws provided).



